Your shopping cart is empty!
Lewmar Pro/Pro Fish Windlass Parts
Gen 1 Serial Numbers Start with 560, 562, 564, 570
Gen 2 Serial Numbers Start with 561, 563, 565, 571
Gen 3 Serial Numbers Start with 566, 567, 569, 572
* This schematic is for Second Generation (2G) Kits for use on Pro-Series/Fish windlasses. For earlier or later kits please check the manual supplied with your windlass or download it from the link on this page..
| 1-2 | Clutch nut & Cone Kit | 66000098 |
| 3 | Gypsy RC 7mm (1/4") | 66000769 |
| Gypsy RC 8mm (5/16") | 66000101 | |
| Gypsy 5/16" G4 | 66000102 | |
| Gypsy RC 6mm | 66000112 | |
| 4 | Stripper arm | 66000096 |
| 5 | Maincase | N/A |
| 6-7-8 | Control arm kit | 66000097 |
| 9 | Dowel 1/4" x 1 1/4" | 66000104 |
| 10 | Socket HD cap screw 10-24UNC x 3/4" | 66000616 |
| 11 | Motor pinion | 66000107 |
| 12 | Dowel, 6x30mm | 66000104 |
| 13 | Spirol pin, 3x20mm | 660000104 |
| 14 | Teflon flat washer | 66000635* |
| 15 | Needle roller bearing | 66000103 or 66000634 |
| 16 | 1st compound gear | 66000635* |
| 17* | Gear train cover | 66000637* |
| 18 | Socket HD cap screw 10-24UNC x 1 1/4" | 66000104 or 66000637* |
| 19 | Wiper seal | 66000104 or 66000637* |
| 20-21 | Needle roller bearing | 66000103 or 66000637* |
| 22 | 2nd compound gear assembly | 66000635 or 66000636 |
| 23 | External clip | 66000103/104 or 105 |
| 24 | Roller clutch | 66000103 or 66000634 |
| 25* | Mainshaft gear | 66000635* |
| 26 | Needle roller bearing | 66000103 or 66000634 |
| 27 | Dowel, 8x45mm | 66000104 or 66000635* |
| 28 | Drive pins, 5x10mm | 66000098 or 66000104 |
| 29 | Wiper seal | 66000104 |
| 30* | Gypsy drive shaft | 66000635* |
| 31 | Socket head cap screw, 10-24UNC x 1/2" | 66000096 or 66000104 |
| 32 | Motor 12V | 66000107 |
| 33 | Grub screw, 8x 32 UNC x 1/4" | 66000097 |
| 34 | Pivot pin washer | 66000097 |
| 35 | Rubber Grommets | 66000107 |
| 36 | Pro-Fish Drive cap | 66000616 or 66000620 |
| 37 | Pro-fish stopper cam | 66000616 or 66000617 |
| 38,39,42,44 | Pro-Fish Plunger Kit | 66000618 |
| 40,41,43,44 | Pro-FishRetaining Pin Kit | 66000619 |
| 38 to 46 | Pro-Fish Drive Cap Assembly Kit | 66000616 or 66000620 |
| Base mat | 66000100 or 66000108 | |
| Mounting stud, washer & nut (Imperial) | 66000100 | |
| Mounting stud, washer & nut (Metric) | 66000108 | |
| Clutch lever | 66000099 | |
| 45 | Pro Fish Shoulder Bolt | 65001106 |
Includes stripper and fasteners for Lewmar Pro Series windlasses...
Socket Head Shoulder Bolt #45 on schematic fits Lewmar Pro Fish windlasses. Lewmar only sells this p..
Replacement motor for Lewmar Pro Series and Pro Fish windlasses. Fits Pro 700. Pro 1000, Pro Fish..
For Pro Series Gen 3 Only - Includes parts 26(1), 33(1), 38(1), 45(1), 50(2), 52(3) from the Pro Ser..
Includes parts 36(1), 38(1), 39 (1), 40(1) 41(1) 42(1) 43(1) 44(1) 45(1) 46 (1) from the Pro Series ..
Gypsy fits Lewmar Pro Series windlass. Use with 1/4" HT chain...
Kits are for use on Pro-Series/Fish with Serial Nos starting 561***, 563***, 565***, 571***, for ear..
Bearing kit for second generation Pro Series windlasses.Second Generation (2G) Kits are for use on P..
P2 Marine
306 S Lake Dr
Stevensville, MD 21666
USA
Toll Free: (800) 456-6740
Local: (443) 569-8529
Email: [email protected]
Office Hours: M-F 8:30:-5:00 Eastern